Shop for Beads & Supplies:
This Week: 30% off 300 Beads & Supplies!

Chakra Wire-Wrapped Earrings & Bracelet Set

AndreaP at Lima
Chakra Wire-Wrapped Earrings & Bracelet Set
Chakra Wire-Wrapped Earrings & Bracelet Set

Additional Images:

Chakra Wire-Wrapped Earrings & Bracelet Set

Project details:

in favorites

I wanted to use the teardrop focals in an interesting way. I liked the hammered textured element of the teardrops. I thought a wire-wrapped design would work nicely. The gemstone Chakra strands are an easy way to create a proper Chakra color layout, (purple to red). Check out our meaningful gemstones page to learn more about Chakra. This set definitely gives off good vibes.

Supplies you’ll need:

You will need 2 teardrop focals, a pair of ear wire, 24 gauge silver wire, I added two different sized spools of wire in the "buy these products list), half strand of crystal beads, I used the rock crystal bicones, 1 strand of energy tube Chakra gemstones, 1 ft of textured oval silver chain, half strand of 6mm lava rock beads, 2 jump rings, and a clasp. This includes what you need for the bracelet as well.

Step-by-Step Instructions:

Step

Step 1

Cut about 8" of wire, start wrapping one end one wire around the teardrop focal. I wrapped it around 3 times. Slide a Chakra energy tube bead on, be sure you are start in the correct Chakra order. Purple-Blue-Light Blue-Green-Tiger Eye(orange)-Yellow-Red. Check out our Meaningful Gemstone page for more Chakra information. seven chakras

Step

Step 2

Feed the wire through the bead and go up and over the teardrop and around again. Push the wrapped wire together to create a clean look.

Step

Step 3

When you get to the end wrap the excess wire around 3 times to finish. Use wire cutters to trim off any excess wire on both sides.

Step

Step 4

Slide s Rock Crystal Bicone onto a head pin.

Step

Step 5

Use a pair of round nose pliers to create a small loop (big enough for your jump ring to go through). Wrap the excess wire around and trim.

Step

Step 6

If you want to make the bracelet, slide the Chakra energy tube beads onto a 7.5" piece of wire.

Step

Step 7

Move the beads close to one side, create a loop on the short end.

Step

Step 8

Take the extra wire at the other end, you will need to create a first and wrapping it around the loop a couple of times, then start going around the beads on a diagonal.

Step

Step 9

To create the lava bead links, just cut a 3" piece of wire, slide the bead on, wrap one end of the wire around a chain link to create a loop, then wrap the excess wire around and trim. Do this on both sides. I added a bead link in every 3 large ovals length. Just trim your chain to add your bead links where you want. Use jump rings to attach the chain to your Chakra link and to attach your clasp.

Buy Products from this Project

15-16" strand
1$13.95
2-4$12.83
5+$11.58
per foot
1-2$2.40
3-5$2.11
6+$1.99
Package of 20
1-2$1.10
3-9$0.99
10+$0.93

Also available: Package of 100

Package of 40
1-2$1.20
3-9$1.08
10+$1.02

Also available: Package of 200

15 yd. spool
1$7.40
2-4$6.81
5+$6.29
Package of 40
1-4$0.70
5-9$0.63
10+$0.55
15-16" strand
1$11.80
2-4$10.86
5+$9.79
½ strand (loose)
$6.40